Sunday, December 31, 2006

So long 2006, see you on the road in '07




(photos: collection of Everett Barnes)

Wednesday, December 27, 2006

More than you ever really wanted to know about sidedraft elbow clamps

I never knew there was more than one version of the clamp that holds the rubber air intake elbow to the 32-PHN air cleaner, but while putting things back together I realized I had two very different clamps to choose from:





I don't know if one is a later design development or if they were just from different suppliers. I have an owner's manual dated 11/61 that shows the one on the left, but I'll probably end up using the one on the right. It works better and it's a more elegant design solution overall.

A very different clamp was shown in early press photos and the 1961 edition of the VW 1500 Workshop Manual:



It seems to be a rubber strap. This design must have been superseded just before production began. It does explain that odd indentation found on the top of most sidedraft air cleaners though.

Air cleaner restoration

Knecht air cleaner, before and after:




It was pretty rough to begin with. I did some very careful straightening of the dents I could reach, then smoothed out the remaining problem areas with lots of sanding, painting, more sanding, and more painting. With the reproduction decal applied it's done.

Sunday, December 24, 2006

Brussels, 1969



If you look closely (click to enlarge) you'll find a Type 34 Ghia and a Variant, as well as a new 411, several Beetles, and a Type 1 Ghia. Merry Christmas!

Friday, December 22, 2006

Why a VW 1500 Karmann-Ghia?

Q: Why was I drawn to a somewhat sporty 2-door rear-engined car from the early '60s with a pronounced beltline?



A: Behavioral conditioning. Here's my family having a picnic at a park in Santa Barbara, California in April 1963. That's a 9-month-old me in the playpen trying to get a better look at my dad's '62 Corvair convertible.

Sunday, December 17, 2006

More progress

I had to sideline the Ghia project for a while for some much needed roof repair and general waterproofing on the house (it doesn't rain very often in Southern California, but when it does...), but this weekend I was finally able to spend some time with the engine. A few weeks ago I was stopped cold by stripped threads in the case. I was trying to install the front half of the fan housing and the case threads for the left side mounting bolt decided to let go. I tried drilling and tapping the threads a little deeper and using a longer bolt but the few threads that were left wouldn't hold. I needed to find the strongest, most permanent solution since these bolts are notorious for coming loose over time anyway. Jim Adney on the vwtype3.org list suggested using thread-locking helicoils. I wasn't familiar with the thread-locking version, but a quick Google search led me to them.



Locking helicoils aren't the easiest thing to find but they're a great thing to know about. They have an eccentric coil that holds the threads in tension, keeping the bolt from loosening. I was able to find 15mm M6 inserts, which are another half as long as the ones that are normally available.



Here's the right side one installed. I decided to do both for peace of mind, since the magnesium alloy case material is relatively soft. I was worried about drilling too deep on the right side -- the left side isn't a problem because if you drill too far it will break through to an area outside the case, but on the right side it will break through inside. Jim was kind enough to measure the case thickness on an old case in his shop, and on the right side it's only 20mm thick. A slight miscalculation would mean splitting the case to clean the shavings out, so I decided to drill only as far as absolutely necessary for the helicoil tap (17mm), and while it was a little nerve-wracking it all went according to plan. Now I can use 20mm bolts instead of the original 15mm, and since the helicoil threads are stainless steel the fan housing mounting will be stronger than what came from the factory.



I used the factory tool VW 177 to center the front half of the fan housing. The procedure is to position the centering tool, then rotate the fan housing counterclockwise until it stops at the split in the case, then tighten the two main bolts. This should be done with the crankcase breather stand and cooling tin screws loosened.



VW originally used shake-proof star washers with the fan housing bolts to keep them from loosening. They're a little funky but I figure VW knew what they were doing.



Here are the fan housing, fan, and pulley installed.



I used the factory 6V flywheel lock VW 215b while torquing the fan pulley bolt. I tightened the bolt to 36 ft. lbs. as recommended by Henry Elfrink's Volkswagen Type 3 Technical Manual, but Russ Wolfe pointed out to me that it should actually be 90 or 100 ft. lbs. according to factory specs. John Muir's How to Keep Your Volkswagen Alive also contains this error, so Type 3 engine builders beware. The Muir book is widely known to have errors, especially in the information about Type 3s, but it's a surprise to me that Elfrink got it wrong. He's usually pretty reliable. Thanks for the heads up, Russ!



The air intake housing is in place.



The generator and coil too. The intake manifold is placed loosely in position for the time being -- the manifold and carburetor are next on the agenda. It's starting to look like a Type 3 engine again.

Tuesday, December 12, 2006

Phantom views

VW often provided nice phantom views of its cars in brochures to help explain their features and to illustrate efficient use of space. These are from brochures printed in 1961.



This one makes good use of ink overprinting to make its point.



A comparison of the sedan and Karmann-Ghia. Passenger space, luggage space, and weight distribution are color coded for easy visualization.